|
 
|
|
Support
2612 Maintenance Manual |
|
|
SECTION 1:
FUNCTION AND SPECIFICATIONS
UNPACKING AND SETUP
SECTION 2:
ILLUSTRATIONS & PARTS LIST
FIGURE 1
BASE
FIGURE 2
WATER RESERVOIR, TUBING, "T" VALVES
FIGURE 3
CURING STATION
FIGURE 4
SAFETY COVER
FIGURE 5
2ND BUCKLE CHUTE
FIGURE 6
CURING COVER, MOTOR CONTROL, CONTROL PANEL
FIGURE 7
MOTOR, GEARS, BRACKETS, PLATES, DRIVE CHAIN
FIGURE 8
DRIVE GEARS, CHAIN, WATER WICK, BRACKETS
FIGURE 9
SIDE FRAMES, FOOT, ELECTRICAL
FIGURE 10
F312 SHEET FEEDER
FIGURE 11
F312 SHEET FEEDER CONTINUED
The INFOSEAL model 2612 is one-step self-contained tabletop folder/sealer
for self-mailer forms. It accepts either sheet-fed or web-fed (continuous)
forms treated with water-activated glue, moistens them, folds them
in a buckle-chute folder, and seals them. It is not for use with
heat-sealed forms. For unglued forms, you can retract the water
system and use the 2612 as a non-sealing folder.
Electrical 120 Vac, 60 Hz: 205 Amp.
Water 2 gallons
Footprint 40" wide x 21" deep
Width 26 ½" alone, 40" with
stacker tray, 43 ½" with sheet feeder, 59" with
sheet feeder and stacker tray
Depth 21"
Height 21 ½" alone, 25 ½"
with sheet feeder.
Weight 135 lbs. Shipped wt; 110 lbs. Installed
Floor Space 36 ½" x 19"
(30" high table recommended)
Forms Size 8 ½" wide, 7"
to 17" long (sheet feeder), 9 ½" wide (before trim),
7" to 17" long (2614 burster)
Forms Weight 20 lb. Minimum to 28 lb. Maximum
1. Check package for shipping damage. If there is shipping damage
do not discard the box.
2. CAUTION: Two people must lift the machine out of the box.
3. Unpack the sheet feeder and install it onto the 2612.
4. Plug cord into wall outlet.
Water Tank
The water tank fill port is located under output stacker.
Be sure to fill the water tank before turning machine on. Fill the
water tank to 1" below the top of the tank, and add one tablespoon
of bleach to the tank. Be sure to reinstall the rubber cap after
filling the water tank. NOTE: Adding bleach to the water tank is
recommended once per month.
Caution: Never run the machine without water!
2613 Sheet Feeder
The 2613 sheet feeder is attached to the left end of the
unit and latches into place. To install set the two lower notches
in the underside of the sheet feeder on the lower pins of the folder.
Then raise the left end of the feeder, rotating it onto the pins,
until the upper pair of notches drop onto the upper pins. Lower
the feeder so it rests on all pins. Press down firmly on the feeder
until feeder snaps solidly into place.
2620 Power Feeder
For installation of the 2620 feeder refer to the 2620 manual.
Replacing the wicks
Over time the wicks become worn and must be replaced. Remove
the thumbscrews from each reservoir lid and remove the wicks. Replace
the wicks with the adjuster tab facing up and the tapered en (tail)
of the wick in the water. This should be done as often as needed
or once per year.
Left Buckle Chute
The left buckle chute lifts up and out to easily adjust fold
settings. Set the left buckle chute by adjusting the height of each
buckle stop. The stops should be set to the same mark on each side,
so the folds will be straight and parallel. Adjust buckle chute
according to the setting decal on right buckle chute.
Right Buckle Chute
Adjust both stops to the same mark for the form to fold evenly.
Adjust the buckle chutes according to the setting decal on the right
buckle chute.
Stacker Wheels
The stacker wheels must be adjusted according to the length
of the form. Proper shingling requires the wheels to be positioned
further out toward the exit end of the folder when running longer
forms. Shorter forms must shingle under the wheels sooner which
requires the wheels to be positioned closer to the buckle chutes.
NOTE: The hotter the printer the more curl in the paper. However
lowering the temperature may void warranty, and may cause toner
not to bond to paper. There for it is not recommended to lower the
temperature on the printer settings.
Figure 1 Base
| ITEM &
PART # |
DESCRIPTION |
QTY |
|
1 F362000 |
COVER-LEFT (DRIVE SIDE) |
1 |
|
2 360-1232 |
CAP, PAINTED #381-0083 VELCRO PAD |
1 |
|
3 379-0023 |
CLIP-RETAINER – EXTERNAL 3/8" SPINDLE 10MM |
1 |
|
4 320-0048 |
CRANK/HANDWHEEL KNOB ASSEMBLY |
1 |
|
5 1820509 |
SPRING – COMPRESSION- KNOB |
1 |
|
6 F351046 |
BRACKET – SWITCH TIMING |
1 |
|
7 377-0042 |
FLAT WASHER .255 X .566 X .048 |
1 |
|
8 373-0094 |
SCREW 6-32 X .50 W/EXT STAR |
2 |
|
9 F380004 |
INPUT ROLLER AND SHAFT ASSEMBLY 1" |
1 |
|
10 F380011 |
INPUT ROLLER AND SHAFT ASSEMBLY 1.5" |
1 |
|
11 F380009 |
DRIVER ROLLER ASSEMBLY 2" |
1 |
|
12 F380005 |
ROLLER AND SHAFT ASSEMBLY – 1ST FOLD |
1 |
|
13 F380010 |
MAIN DRIVER ROLLER AND SHAFT ASSEMBLY |
1 |
|
14 F380006 |
ROLLER AND SHAFT ASSEMBLY – 2ND FOLD |
1 |
|
15 F380007 |
ROLLER AND SHAFT ASSEMBLY – UPPER IRONING |
1 |
|
16 F380008 |
SHAFT ROLLER ASSEMBLY – LOWER IRONING |
1 |
|
17 F320001 |
SPRING - COMPRESSION |
12 |
|
18 F384011 |
SPRING - COMPRESSION |
2 |
|
19 F362007 |
BEARING – FRAME 2216 |
20 |
|
20 F362043 |
SUPPORT SPRING |
2 |
|
21 F365001 |
BELT – CURING STATION - BOTTOM |
5 |
|
22 F380068 |
IRONING DECK ASSEMBLY |
1 |
|
23 F313001 |
ROLLER – DRIVE OUTPUT |
1 |
|
24 F313000 |
ROLLER - OUTPUT |
1 |
|
25 5450237 |
SHIM OSCILLATOR WASHER-HANDWHEEL KNOB |
1 |
|
26 F380075 |
MYLAR KICKER ASSEMBLY 2612 |
1 |
|
27 F362023 |
STRIP – KICK DOWN |
1 |
|
28 F351049 |
CLAMP – MYLAR KICKER |
1 |
|
29 373-0088 |
SCREW 8-32 X ¼" PSPN |
1 |
|
30 F310020 |
SHAFT – SWITCH TIMING |
1 |
|
31 311-0044 |
COUNTER SWITCH 17" – TIMING SHAFT |
1 |
|
32 F362001 |
COVER – RIGHT (OPERATOR SIDE) |
1 |
|
33 325-0259 |
DECAL, DOCUSEAL 2612, #326-0091 LABEL, 2612 |
2 |
|
34 F380062 |
CURING STATION LOCK BRACKET ASSEMBLY |
1 |
|
35 373-0095 |
SCREW 8 – 32 C .375 PSPN |
4 |
|
36 F384014 |
BEARING, FLANGED |
2 |
|
37 F380080 |
TENSIONER, ASSEMBLY |
2 |
|
38 F332000 |
SHEET FEEDER DRIVE GEAR 20T |
|
|
39 381-2845 |
PIN/HANDWHEEL, 1/8 DIA. SPRING PIN |
|
|
40 381-0018 |
SPRING PIN/PULLEY 1/8 X 1 |
|
|
41 373-0016 |
COVER SCREW 10-32 X ½ LG |
|
|
42 377-2809 |
STAR WASHER FOR COVER SCREW #10 |
|
|
43 381-0011 |
COVER CLIP |
|
|
390-0290 |
3324 INTERFACE ASSY (NOT SHOWN) |
|
Figure
2 Water Reservoir, Tubing, "T" Valves
FIG. 2 – WATER RESERVOIR, TUBING, "T"
VALUES PARTS LISTING
| ITEM &
PART # |
DESCRIPTION |
QTY |
|
1 F362041 |
VALVE - "T" FITTING |
2 |
|
2 F362019 |
VALVE – " T" FITTING |
1 |
|
3 F362034 |
TUBING- PVC VALVE |
4 |
|
4 F362033 |
TUBING- PVC |
1 |
|
5 F362032 |
TUBING- WICK – LEFT & RIGHT 3/8" |
2 |
|
6 F362047 |
TUBING- WATER RESERVOIR |
1 |
|
7 F362046 |
RESTRICTOR |
1 |
|
8 F362048 |
TUBING - PVC |
1 |
|
9 F362040 |
TUBING - ¼" |
1 |
|
10 F362030 |
TUBING - PVC |
1 |
|
13 F 362031 |
TUBING - PVC |
2 |
Figure 3
Curing Station
FIG. 3 – CURING STATION PARTS LISTING
| ITEM &
PART # |
DESCRIPTION |
QTY |
|
1 F380030 |
CURING STATION ASSEMBLY - COMPLETE |
1 |
|
2 F310010 |
CURING STATION DRIVE SHAFT ASSEMBLY |
1 |
|
3 F310011 |
CURING STATION ENTRY IN SHAFT ASSEMBLY |
1 |
|
4 F310012 |
SHAFT – EXIT – CURING STATION |
2 |
|
5 F313003 |
ROLLER – CURING STATION |
2 |
|
6 376-6559 |
10-32 X ½ KNURLED CUP POINT SET SCREWS |
4 |
|
7 F365000 |
BELT – CURING STATION - TOP |
4 |
|
8 F380061 |
CURING STATION BRACKET ASSEMBLY |
1 |
|
9 175-0144 |
BEARING, FLANGED |
4 |
|
10 F351035 |
BRACKET – CURING STATION |
1 |
|
11 F323003 |
SPRING – ROLLER STACK |
2 |
|
12 F362007 |
BEARING FRAME 2216 |
2 |
|
13 F362052 |
ACETATE STACKER |
1 |
|
14 F310021 |
SHAFT – SAFETY COVER |
2 |
|
15 F351066 |
LONG FORM ACCESSORY |
1 |
Figure 4
Safety Cover
FIG. 4 – SAFETY COVER PARTS LISTING
| ITEM &
PART # |
DESCRIPTION |
QTY |
|
1 F362044 |
COVER – SAFETY |
1 |
|
2 F380015 |
FIRST BUCKLE CHUTE ASSEMBLY |
1 |
|
3 F350001 |
SPACER PLATE SIDE |
2 |
|
4 F350002 |
SPACER PLATE TOP |
1 |
|
5 F311003 |
STUD PLATE |
1 |
|
7 F351007 |
STOP 1ST BUCKLE CHUTE |
1 |
|
8 F351009 |
FRAME 1ST BUCKLE CHUTE |
1 |
|
9 F380017 |
1ST BUCKLE CHUTE GUIDE ASSEMBLY |
1 |
|
10 1416119 |
NUT KNURLED |
2 |
|
11 25-0018 |
CLIP RETAINER BOWED |
1 |
|
12 375014 |
WASHER PLATE STUD |
1 |
|
13 3165503 |
SCALE BUCKLE CHUTE |
2 |
|
14 80-0072 |
NUT SELF TAPPING |
9 |
|
15 73-0501 |
SCREW 6 – 32 X 5/16" – PPN |
10 |
|
16 50-0007 |
WASHER PLAIN - .056" X .375" X .051 |
10 |
|
17 71-0003 |
NUT 6 – 32 X 5/16" – LW |
10 |
|
18 F384012 |
SAFETY COVER HINGE ASSEMBLY |
1 |
|
19 F351063 |
BRACKET SAFETY COVER |
1 |
|
20 200-0701 |
ACTUATOR |
4 |
|
21 72-0283 |
SCREW 8 – 32 X 3/8" PSPN |
4 |
|
22 71-0001 |
NUT 4 – 40 X ¼" – LW |
4 |
|
23 F380028 |
2ND BUCKLE CHUTE ASSEMBLY COMPLETE |
1 |
|
24 F351012 |
SHIELD HAMMESS |
1 |
|
25 72-0611 |
SCREW 8 – 32 X 3/8" PSPN |
5 |
|
26 F367001 |
ABSORBER FELT |
1 |
|
27 F365002 |
GATE – HAMMER |
3 |
|
28 F362011 |
HAMMER – GATE |
3 |
|
29 F362012 |
DEFLECTOR – HAMMER GATE |
3 |
|
30 60-8162 |
SCREW |
3 |
|
31 F370000 |
SCREW – HAMMER ADJUSTING |
3 |
|
32 F351053 |
CLAMP GATE |
3 |
|
33 F380031 |
HAMMERS BRACKET ASSEMBLY |
1 |
|
34 F362018 |
STOP NYLON |
2 |
|
35 15-0504 |
FASTENER PUSH-ON |
2 |
|
36 F310006 |
SHAFT HAMMERS BRACKET |
1 |
|
37 23-0025 |
CLIP RETAINER – ¼" SPINDLE |
12 |
|
38 25-0018 |
CLIP RETAINER BOWED |
2 |
|
41 200-0900 |
MAGNETIC PROX. SENSOR |
1 |
Figure 5
2nd Buckle
FIG. 5 2ND BUCKLE CHUTE PARTS LISTING
| ITEM &
PART # |
DESCRIPTION |
QTY |
|
1 F380028 |
2ND BUCKLE CHUTE ASSEMBLY - COMPLETE |
1 |
|
2 1416119 |
NUT – KNURLED KNOB OD |
3 |
|
4 F311003 |
STUD – PLATE |
4 |
|
5 379-0024 |
"E" RING CLIP – RETAINER – BOWED/SHAFT 0.188 |
4 |
|
6 375014 |
WASHER – PLATE STUD |
2 |
|
7 F318001 |
SPACER – SECOND BUCKLE CHUTE |
2 |
|
8 379-0028 |
"E" RING CLIP – BOWED/SHAFT 0.250 |
4 |
|
9 F351017 |
GUIDE – 2ND BUCKLE CHUTE |
|
|
10 F380035 |
FRONT 2ND BUCKLE CHUTE ASSEMBLY |
1 |
|
11 3165503 |
DECAL – BUCKLE CHUTE |
2 |
|
12 F351054 |
CLAMP – TUBING |
1 |
|
13 F362048 |
TUBING – PVC |
1 |
|
14 78-0835 |
SCREW – 10-32 X 5/8" – PFUC |
1 |
|
15 F310005 |
SHAFT – LATCH |
1 |
|
16 379-0079 |
"E" RING BOWED CLIP HD, 0.18 |
2 |
|
17 F380033 |
LATCH ASSEMBLY – RIGHT HAND |
1 |
|
18 F380034 |
LATCH ASSEMBLY – LEFT HAND |
1 |
|
19 F320000 |
SPRING – TENSION |
2 |
|
20 F361010 |
LABEL – BUCKLE CHUTE SETTING |
2 |
|
21 315-0039 |
CLAMP WIRE 0.312 – TUBING |
2 |
|
22 F380013 |
WICK TANK ASSEMBLY – COMPLETE |
1 |
|
23 F380012 |
FLAP TANK ASSEMBLY |
1 |
|
24 F362016 |
COVER – WICK TANK |
1 |
|
25 F380018 |
WICK CARTRIDGE COMPLETE/COTTON ALONE F367000 |
3 |
|
26 375-0093 |
THUMB SCREW 8-32 X 7/16" – PPN |
3 |
|
27 F380087 |
WATER RETURN BLOCK ASSEMBLY |
1 |
|
28 378-0116 |
NUT W/HEXAGON SOCKET 10-32 WATER RETURN BLOCK |
2 |
|
29 F362030 |
TUBING – PVC |
1 |
|
30 F362040 |
TUBING – PVC ¼" |
1 |
|
31 378-0004 |
#10 KEP NUT (10-32) |
1 |
|
32 F380032 |
PLATE |
|
|
33 F311011 |
STUD CLAMP – BUCKLE CHUTE |
|
|
34 377-0042 |
WASHER, FLAT .255 X .566 X .048 |
|
|
35 F362027 |
HOSE NIPPLE – FITTING DRAIN ¼" |
|
Figure
6 Curing Cover, Motor Control, Control Panel
FIG. 6 – CURING COVER, MOTOR CONTROL, CONTROL PANEL PARTS
LISTING
| ITEM &
PART # |
DESCRIPTION |
QTY |
|
1 395-0729 |
2625 URGE ROLLER KIT FOR 2612 |
1 |
|
2 320-8135 |
STACKER WHEEL |
5 |
|
3 360-1699 |
SKI ASSEMBLY |
1 |
|
4 373-0092 |
SCREW – 4-40 X ½" – PSPN |
4 |
|
5 378-0111 |
NUT – 4-40 X ¼" – LW |
4 |
|
13 378-0110 |
NUT – 10-32 X 3/8" – LW |
8 |
|
14 F380090 |
CONTROL ASSEMBLY – COMPLETE |
1 |
|
15 F380089 |
CONTROL PLATE ASSEMBLY |
1 |
|
16 314-0090 |
BLOCK – TERMINAL 1-ROW, 10-POS. |
2 |
|
17 325-0247 |
MARKING STRIP – TERMINAL 10-POS. |
2 |
|
18 373-0090 |
SCREW 6-32 X 5/8" – PSPN |
6 |
|
19 390-0666 |
TRANSFORMER ASSEMBLY |
1 |
|
20 373-0088 |
SCREW 8-32 X ¼" – PSPN |
2 |
|
21 314-0009 |
TERMINAL – STRIP – 4 PIN – SINGLE ROW |
1 |
|
22 325-0248 |
STRIP – TERMINAL , 4-POS |
1 |
|
23 F384008 |
SOCKET – RELAY MOUNTING |
1 |
|
24 373-0089 |
SCREW 4-40 X 7/8" – PSPN |
1 |
|
25 F384007 |
RELAY ASSEMBLY |
1 |
|
26 F384009 |
CLIP – RELAY MOUNTING |
1 |
|
27 F384005 |
DC MOTOR CONTROL ASSEMBLY |
1 |
|
28 373-0010 |
SCREW 4-40 X ½" – PSPN |
4 |
|
29 350-0067 |
GROMMET .150 ID – RUBBER |
4 |
|
30 381-0081 |
STANDOFF – CONTROL GAS SPRING 17" |
4 |
|
31 373-0095 |
SCREW 8-32 X 3/8" – PSPN |
4 |
|
32 F380022 |
CONTROL PANEL ASSEMBLY |
1 |
|
33 390-0662 |
CONTROL PANEL COUNTER ASSEMBLY |
1 |
|
34 319-0155 |
INDICATOR – BLUE ASSEMBLY |
1 |
|
35 319-0156 |
INDICATOR – RED ASSEMBLY |
1 |
|
35A 319-0157 |
LAMP, 24V. .037A |
1 |
|
36 F362003 |
KNOB – SPEED CONTROL |
1 |
|
37 F323003 |
"D" SPRING/SPEED KNOB |
1 |
|
38 F384013 |
SPEED CONTROL POT ASSEMBLY 5K, 75W |
1 |
|
39 311-0094 |
ON-OFF SWITCH – ROCKER |
1 |
|
40 F362002 |
PANEL – CONTROL |
1 |
|
41 F362050 |
GUARD – SWITCH |
1 |
|
42 377-0042 |
WASHER – PLAIN .255 X .566 X .048 |
2 |
|
43 F361033 |
TERMINAL BLOCK COVER |
1 |
|
44 F3462550 |
DECAL ELECTRICAL HAZARD |
|
Figure
7 Motor, Gears, Brackets, Plates, Dr. Chain
FIG. 7 – MOTOR, GEARS, BRACKETS, PLATES, DR. CHAIN PARTS
LISTING
| ITEM &
PART # |
DESCRIPTION |
QTY |
|
1 F337002 |
PULLEY – 14 GRV – 1/5P DRIVE |
1 |
|
2 F337005 |
PULLEY – 19 GRV – 1/5P DRIVE |
1 |
|
3 390-0665 |
MAIN DRIVE MOTOR ASSEMBLY |
1 |
|
4 375-0096 |
¼-20 HEX HD SCREW W/ ET STAR |
4 |
|
5 377-1813 |
¼" WASHER "W" |
4 |
|
6 F323001 |
SPRING G – WICK |
1 |
|
7 375-0055 |
SCREW 4 – 40 X ¼" BUTTON HEAD |
2 |
|
8 F380052 |
WICK SPRING MOUNTING BRACKET ASS. - RIGHT |
1 |
|
9 373-0094 |
SCREW 6-32 X ½" – PPS |
2 |
|
10 F350008 |
SPACER – MOTOR |
1 |
|
11 244-0101 |
CHANNEL – RUBBER |
1 |
|
12 F311005 |
STUD – PIVOT TENSION |
1 |
|
13 F380020 |
TENSION ROLLER ASSEMBLY |
1 |
|
14 F337001 |
PULLEY – 28 GVR – 1/5P |
1 |
|
15 F380021 |
PULLEY ASSEMBLY – 21 GROOVES |
1 |
|
16 379-0014 |
CLIP – RETAINER – 3/8" SPINDLE |
4 |
|
17 F337000 |
PULLEY – 21 GRV – 1/5P |
1 |
|
18 F380019 |
TENSIONER BRACKET ASSEMBLY |
1 |
|
19 377-0042 |
WASHER – PLAIN .255 X .566 X .048 |
2 |
|
20 373-0096 |
SCREW 10-32 X 3/8" – PSPN |
2 |
|
21 F380029 |
RETAINER BEARING ASSEMBLY |
2 |
|
22 365-0137 |
TIMING BELT 300 X L037 PULLEY, FEED ROLLER DR. |
1 |
|
23 365-0136 |
TIMING BELT 210 X L037, MAIN DRIVE |
1 |
|
24 F320005 |
SPRING – TENSION |
2 |
|
25 F380080 |
TENSIONER ASSEMBLY |
2 |
|
26 371-0076 |
BEARING ALIGN 0.37 – FLANGED |
2 |
|
27 F311020 |
STUD – FEEDER MOUNTING |
2 |
|
28 F351055 |
LEVER – AUTO ADJUSTING – RIGHT |
1 |
|
29 5611526 |
SCREW – SHOULDER – 10-32 |
2 |
|
30 F351056 |
LEVEL – AUTO ADJUSTING – LEFT |
1 |
|
31 F311016 |
STUD – PIVOT |
2 |
|
32 F337004 |
PULLEY – 60T – 1/5P |
1 |
|
33 F380047 |
INPUT GUIDE ASSEMBLY |
1 |
|
34 F380053 |
WICK SPRING MOUNTING BRACKET ASS. - LEFT |
1 |
Figure
8 Drive Gears, Chain, Water Wick, Bracket
FIG. 8 – DRIVE GEARS, CHAIN, WATER WICK, BRACKET PARTS
LISTING
| ITEM &
PART # |
DESCRIPTION |
QTY |
|
1 F380045 |
BRACKET – ROLLER |
1 |
|
2 23-0031 |
CLIP – RETAINER – 5/16" SPINDLE |
1 |
|
3 373-0096 |
SCREW – 10-32 X 3/8" – PSPN |
2 |
|
4 F310009 |
SHAFT – GEAR PULLEY |
1 |
|
5 F333000 |
GEAR – 80T |
2 |
|
6 3131069 |
SPROCKET – 250P - .3771D (16T) |
1 |
|
7 376-0078 |
10-32 X ¼ KNURLED CUP PT SCREW SET |
2 |
|
8 F333001 |
GEAR – 28T/64T |
2 |
|
9 23-0025 |
CLIP – RETAINER ¼" SPINDLE |
3 |
|
10 F335000 |
GEAR – CONVEYOR DRIVE |
1 |
|
11 F380063 |
SPROCKET ASSEMBLY – 16T |
2 |
|
12 F311000 |
STUD – UPPER GEAR |
1 |
|
13 F311002 |
STUD – CENTER GEAR |
1 |
|
14 F380064 |
ARM/ STUD ASSEMBLY |
1 |
|
15 422101 |
SPRING – TENSION |
1 |
|
16 F315000 |
COLLAR – SPRING |
1 |
|
17 376-0069 |
8-32 X ¼" SOC. SCREW SET |
1 |
|
18 379-0014 |
CLIP – RETAINER – 3/8" SPINDLE |
1 |
|
19 367-0022 |
½" PITCH CHAIN LENGTH 32" - DRIVE |
1 |
|
20 F331001 |
SPROCKET – 24T |
1 |
|
21 311-0084 |
3-AMP CIRCUIT BREAKER ASSEMBLY |
1 |
|
22 373-0092 |
SCREW – 4-40 X ½" – PSPN |
2 |
|
23 310-0039 |
POWER CORD ASSEMBLY, DETACHABLE |
1 |
|
24 378-0111 |
NUT – 4-40 X ¼" – LW |
1 |
|
25 F380043 |
TANK COVER ASSEMBLY |
1 |
|
26 F380044 |
OUTPUT DECK ASSEMBLY |
1 |
|
28 F365004 |
CAP- WATER TANK |
1 |
|
30 F38000 |
MOTOR SHIELD ASSEMBLY |
1 |
|
31 319-0161 |
RFI FILTER – INPUT COVER |
1 |
|
32 F383005 |
2612 MAIN HARNESS ASSEMBLY |
1 |
|
33 F361001 |
LABEL – UL/ BUCKLE CHUTE |
1 |
|
34 F380024 |
WICK TANK – RIGHT HAND |
1 |
|
35 F380025 |
WICK TANK – LEFT HAND |
1 |
|
36 F380046 |
ENTRY GUIDE ASSEMBLY – UPPER |
1 |
|
37 395-0706 |
2612 WATER TANK RESERVOIR W/ WATER PUMP KIT |
1 |
|
38 F383008 |
WATER LEVEL SENSOR ASSEMBLY |
1 |
|
40 373-0094 |
SCREW 6-32 X ½" – PSPN |
2 |
|
41 F380048 |
PUMP MOUNTING BRACKET ASSEMBLY |
1 |
|
42 F380054 |
BASE PLATE ASSEMBLY |
1 |
|
43 375-0093 |
8-32 THUMBSCREW |
4 |
|
44 F362006 |
COVER, WICK TANK HOUSING |
1 |
|
45 F380018 |
WICK CARTRIDGE COMPLETE/ COTTON ALONE F367000 |
1 |
|
46 F384019 |
WATER BOTTLE |
1 |
Figure
9 Side Frames, Foot, Electrical
FIG. 9 – SIDE FRAMES, FOOT, ELECTRICAL PARTS LISTING
| ITEM
& PART # |
DESCRIPTION |
QTY |
|
1 3385037 |
BOLT – FOOT, ADJUSTABLE |
4 |
|
2 378-0011 |
NUT – 3/8 – 16 X 9/16 – LW |
4 |
|
3 F380055 |
SIDE FRAME ASSEMBLY – RIGHT |
1 |
|
4 F380056 |
SIDE FRAME ASSEMBLY – LEFT |
1 |
|
5 314-0089 |
CLAMP, CABLE |
2 |
|
6 F351027 |
COVER – PUMP INLET |
1 |
|
7 373-0095 |
SCREW 8-32 X 3/8" - PSPN |
4 |
|
8 F362032 |
3/8" TUBING – WICK - LEFT |
2 |
|
9 F362031 |
TUBING - PVC |
1 |
|
10 319-1884 |
CABLE TIE |
12 |
|
11 F362033 |
TUBING - PVC |
1 |
|
12 F383005 |
2612 MAIN HARNESS ASSEMBLY |
1 |
|
13 F383006 |
CONTROL PANEL HARNESS ASSEMBLY - POWER |
1 |
|
14 F383009 |
CONTROL PANEL HARNESS ASSEMBLY |
1 |
|
15 F383013 |
RELAY HARNESS ASSEMBLY |
1 |
|
16 F383011 |
POWER CONTROL HARNESS ASSEMBLY |
1 |
|
17 F383001 |
LOWER VOLTAGE HARNESS ASSEMBLY |
1 |
|
18 F383008 |
WATER LEVEL SENSOR ASSEMBLY |
1 |
|
19 F383012 |
CONTROL SWITCH HARNESS ASSEMBLY |
1 |
|
20 F383000 |
BURSTER HARNESS ASSEMBLY - RECEPTACLE |
1 |
|
21 227-0017 |
CLAMP - HARNESS |
3 |
|
22 315-5853 |
PANDUIT TIE WRAPS 1.51 MP |
1 |
|
23 315-5800 |
MOUNT – CABLE TIE |
1 |
|
24 378-0013 |
NUT 8-32 X 11/32" LW |
3 |
|
25 314-0088 |
USE #315-0019 CABLE MOUNT |
4 |
|
26 F383012 |
CONTROL SWITCH HARNESS ASSEMBLY |
1 |
|
27 F380001 |
COLLECTOR ASSEMBLY STACKER |
1 |
|
28 F362013 |
BRACKET - COLLECTOR |
2 |
|
29 373-0086 |
SCREW – SELF-TAPPING 10-32 X ½" FLAT HEAD |
4 |
|
30 378-0098 |
10-24 HEX NUT |
4 |
|
31 F351004 |
BRACKET – SUPPORT - COLLECTOR |
2 |
|
32 351-0009 |
GROMMET – RUBBER BUMPER |
2 |
|
33 3187613 |
CONVEYOR COVER HARNESS ASSEMBLY |
2 |
|
34 373-0092 |
SCREW 4-40 X ½" PSPN |
4 |
|
35 377-0040 |
.125 X .312 X .030 WASHER |
4 |
|
36 378-0111 |
NUT – 4-40 X ¼" - LW |
4 |
|
37 F312003 |
PIN – BUCKLE PLATE MOUNTING |
1 |
|
37A 378-0013 |
NUT |
1 |
Figure 10
F312 Sheet Feeder
FIG. 10 – F312 SHEET FEEDER PARTS LISTING
| ITEM &
PART # |
DESCRIPTION |
QTY |
|
1 F380038 |
SIDE GUIDE ASSEMBLY - LEFT |
1 |
|
2 F380037 |
SIDE GUIDE ASSEMBLY - RIGHT |
1 |
|
3 F380042 |
FEEDER HOOK ASSEMBLY - LEFT |
1 |
|
4 F380041 |
FEEDER HOOK ASSEMBLY - RIGHT |
1 |
|
5 F362022 |
COVER – FEEDER GEAR |
1 |
|
6 373-0084 |
8-16 TAPPING SCREW |
2 |
|
7 373-0016 |
10-32 X ½" SCREW - PSPN |
10 |
|
8 379-0026 |
CLIP – RETAINER – 51/6 - SPINDLE |
2 |
|
9 377-0043 |
FLAT WASHER .376 X .876 X .060 |
2 |
|
10 F333002 |
GEAR – FEED ROLLER |
2 |
|
11 F380060 |
GEAR LINK FEEDER ASSEMBLY |
1 |
|
12 378-0110 |
NUT – 10-32 X 3/8" - LW |
3 |
|
13 50-0028 |
WASHER .437" X 1.000" X .084" |
14 |
|
14 379-0014 |
CLIP – RETAINER – 3/8" SPINDLE |
8 |
|
15 381-0075 |
SPRING PIN .125 X .625 |
1 |
|
16 F310014 |
SHAFT – ROLLER FEEDER |
1 |
|
17 F333003 |
GEAR - MODIFIED |
1 |
|
18 376-0107 |
6-32 X .375 FLAT TIP SCREW SET |
2 |
|
19 F318004 |
HUB - FEEDER |
2 |
|
20 170-0090 |
BEARING - PLAIN |
1 |
|
21 F380077 |
ADJUSTMENT KNOB ASSEMBLY |
2 |
|
22 376-0006 |
SCREW SET 10-32 X 3/8" FLAT POINT |
2 |
|
23 181821 |
COLLAR – HUB – DRIVE FEED CLUTCH |
2 |
|
24 F380078 |
LH HUB – FEED ROLLER CLUTCH |
1 |
|
25 176706 |
FRICTION WASHER – FEED ROLLER |
2 |
|
26 F384004 |
FEED ROLLER ASSEMBLY |
1 |
|
27 F380079 |
FEEDER CLUTCH HUB ASSEMBLY - RIGHT |
1 |
|
28 F320004 |
COMPRESSION SPRING - TENSION |
7 |
|
29 F380036 |
CONTROL PLATE ASSEMBLY |
1 |
|
390-0756 |
WHOLE SHEET FEED ASSEMBLY |
|
|
30 330-5715 |
COLLAR ¼" I.D. |
2 |
|
30A 376-5809 |
10-32 X 3/16 SETSCREW FOR COLLAR |
2 |
Figure
11 F312 Sheet Feeder Continued
FIG. 11-F312 SHEET FEEDER CONTINUED PARTS LISTING
| ITEM &
PART # |
DESCRIPTION |
QTY |
|
1 F380039 |
FEEDER DECK ASSEMBLY |
1 |
|
2 |
SCREW 6-32 X 3/8" – PFN (NOT IN SYSTEM, NEED # |
4 |
|
3 F380086 |
MTG. STONE ASSEMBLY |
1 |
|
4 F380085 |
STONE BRACKET ASSEMBLY |
1 |
|
5 373-0079 |
SCREW W/ LOCK WASHER |
2 |
|
6 F320004 |
SPRING COMPRESSION |
1 |
|
7 3362018 |
STONE SEPARATOR PP |
1 |
|
8 F310013 |
SHAFT – STONE FEEDER |
1 |
|
9 F380084 |
FEEDER MOUNTING STONE BRACKET ASSEMBLY |
1 |
|
10 342-0022 |
SPRING DATER DOOR - TENSION |
2 |
|
11 377-2811 |
#6 PLAIN WASHER |
4 |
|
12 390-0252 |
FEEDER ADJUSTMENT BRACKET ASSEMBLY |
1 |
|
13 377-0013 |
WASHER PLAIN |
2 |
|
14 379-0009 |
CLIP – RETAINER –3/16" SPINDLE |
2 |
|
15 379-0020 |
CLIP – RETAINER – 1/8" SPINDLE |
2 |
|
16 F380058 |
FEED PLATE ASSEMBLY |
1 |
|
17 373-0016 |
SCREW 10-32 X ½" - PSPN |
2 |
|
18 F351024 |
BRACKET - FEEDER |
1 |
|
19 F350004 |
LINK - FEEDER |
4 |
|
20 F345000 |
BLOCK – THREAD ADJUSTING |
1 |
|
21 377-1813 |
¼" WASHER - PLAIN |
2 |
|
22 379-0008 |
CLIP – RETAINER – ¼" SPINDLE |
2 |
|
23 F312001 |
PIN – ALIGNMENT THREAD |
1 |
|
24 F380059 |
FEEDER BOTTOM COVER ASSEMBLY |
1 |
|
25 |
CLIP ** NOT IN SYSTEM, PART # NEEDED |
2 |
|
26 378-0110 |
NUT 10-32 X 3/8" - LW |
2 |
|
27 373-0016 |
SCREW 10-32 X ½" PSPN |
2 |
|
28 375-0092 |
¼ - 20 THUMBSCREW |
1 |
|
29 330-5715 |
COLLAR ¼" I.D. |
2 |
|
29A 376-5809 |
10-32 X 3/16" SETSCREW FOR COLLAR |
2 |
©
2002-2008, Infoseal.
Infoseal, LLC • 1825 Blue Hills Circle • Roanoke, Virginia •
24012 • 1.888.952.4636 • Fax 888.652.4636
|
